Towel bar: Towel bar is used to hang towels. The installation position is generally a position closer to the bath, and the installation height is generally 1.4 to 1.6 meters from the ground. The installation height should not be too low, otherwise the towel will get wet when bathing. The installation methods of the towel bar can be summarized into two types, one is to install without punching and the other is to install with emptying. Hole-free installation methods generally include vacuum suction cup type and watering type. Screws are generally used for drilling holes. Nowadays, many families prefer the non-punch vacuum suction cup installation, because it is easy to install, fast, and does not require much effort when disassembling. It does not cause any damage to the wall, but after a long time, it is easier to loose and fall off. The fixing force is not as strong as screwing. The watering type, as the name implies, is fixed on the wall with nail-free glue. It takes more time to install, but the cost savings are better than others.
Towel rack: The towel rack is used to place bath towels. The installation location is next to the towel bar or in an open position in the bathroom. You can design the installation location according to the characteristics of your own bathroom. The length and width of the bath towel are several times that of the towel. The height of the installation is naturally higher than that of the towel bar, but it mainly depends on the average height of the family members.
Toilet paper holder: The toilet paper holder is used to place toilet paper. It is generally installed next to the toilet. The installation position should be lower than the toilet. If it is installed higher than the toilet, you can imagine how inconvenient it is.
Toilet brush holder: The toilet brush is generally installed next to the toilet, and it is recommended not to install it next to the toilet paper holder. The toilet brush usually contains bacteria when cleaning the toilet, and then the air around the toilet brush has many bacteria, and the bacteria are easy to adhere to the paper towel.
Storage basket: The storage basket is generally installed near the shower, and is used to place items such as shower gel and shampoo for easy bathing. The installation height is generally one meter two to one meter four. These are just for reference, and are of no practical use. You can design according to your own habits and believe in yourself.
Clothes hook: The characteristics of stainless steel clothes hooks are reflected in high temperature and low temperature resistance according to physical properties, and corrosion resistance and not easy to rust according to chemical properties. They are expensive and expensive, and are suitable for bathroom use. Space aluminum clothes hooks are characterized by not easy to fade, good environmental performance, not easy to rust, and easy to dye. The clothes hooks made of space aluminum materials on the market are rich in colors, strong in decoration, and low in price. The disadvantage is that the pressure resistance is weak. Not suitable for hanging heavy objects, suitable for various places. The copper clothes hook itself has high material density and good stability, so it is not easy to rust, resists pressure and is heavy, and is more expensive in the market. It is suitable for kitchens, living rooms and other places. Aluminum alloy is made of pure aluminum with some alloying elements, so aluminum alloy hooks are slightly better than space aluminum hooks in terms of performance. Zinc alloy is an alloy formed by adding other elements based on zinc, so zinc alloy clothes hooks are characterized by good manufacturability, long use time and easy cleaning. Wooden clothes hooks have low immunity to humid environments, poor physical properties, but strong decoration, suitable for living rooms, bedrooms, study rooms and other locations. Plastic clothes hooks are easy to mold, so most of the plastic clothes hooks on the market are not only highly decorative but also low-cost. The disadvantage is that the surface is not resistant to dirt and it is inconvenient to clean.
When we buy, we must consider the actual situation at home. Choose the right size and the required rack. Don't buy the package blindly. Some things may not be useful.
Of course it does.
What is a wall-mount faucet?
The wall-mounted faucet is to install the water supply pipe in the wall. The faucet is independent, and the wash basin is also independent. The washbasin does not need to be connected with the faucet, so there are more free choices in the washbasin shape. There are more diversified washbasin choices in different spaces and environments.
The place where the washbasin and the faucet are connected is usually the place where rust and bacteria breed the most. With separate faucets and wash basins, you don't have to worry about cleaning these locations.
Two Types of Wall-mounted Faucets.
1. Single Handle Single Hole Wall-mount Mixer Faucet
2. Single Handle Double Hole Wall-mount Mixer Faucet
3. Single Handle Wall-mount Mixer Faucet with Rough-in Valve
Double handle wall-mount faucet means that the hot and cold water are controlled separately. The left is hot and the right is cold, and the water outlet is in the middle. The copper color part in the picture is the concealed part.
The above are several common wall-mount faucets.
Advantages and Disadvantages of Wall-mount Faucet
1. Save space. In-wall faucets generally save space and free up space on the countertop.
2. Easy to clean. It is more convenient to clean the countertop.
3. It is highly decorative. It can increase the diversity of bathroom decoration and make the space more tidy.
1. The price is more expensive. The price and installation cost of the wall-mounted faucet is higher than that of the ordinary faucet.
2. Trouble with installation. Need to ask professional installers to install.
3. Trouble with maintenance. Many parts are installed in the wall. So if something goes wrong, it will be troublesome to repair.
Precautions for the Installation of In-wall Faucets.
1. Due to the concealed installation, the wall-mounted faucet must be installed in the wall together with the water pipe during decoration. Therefore, it is necessary to choose the faucet style before the decoration.
2. Do not remove the protective cover of the product during the decoration construction process to avoid damage to the product.
3. Be sure to pressurize the product to test whether it leaks. Make sure that the water pipe is connected correctly.
4. The sundries at the connection must be removed before installation to avoid blockage or water leakage.
5. The installation height is best controlled at a height of 15~20cm above the basin. The height above the ground is 95cm~100cm.
6. After installing the faucet, attach the wall tiles, etc.
So should you choose an in-wall faucet?
1. The wall-mounted faucet has high appearance and can be matched with various decoration styles according to your own preferences.
2. The wall-mounted faucet has a miraculous effect when used in a bathroom with a relatively compact space, which can save a lot of space.
3. The main concern for the wall-mounted faucet is maintenance, worrying about water leakage. In fact, the wall-mounted faucet is similar to the shower at home. The technology is very mature. It's already very popular.
We can make a comparison with ordinary faucets:
1. The connection method is different: ordinary faucet is connected to the water outlet through angle valve and hose to supply water. The wall-mounted faucet is connected to the water outlet through the concealed part to supply water. The concealed part and the water outlet are installed as a whole. As far as the connection method is concerned, there are fewer steps for the wall mount faucet.
2. Different accessories: common faucet accessories are angle valve, hose and faucet. The wall-mounted faucet accessories are concealed parts and faucets. Because there are no fittings such as angle valves and hoses, the possibility of water leakage from the faucet is lower.
The more complicated the connection method, the more connection points, the more hidden dangers. The hidden danger of in-wall faucets is actually smaller.
So you can buy the wall-mounted faucet with confidence. Ask a professional to install it. There is no problem.
After installation, its usefulness depends on the size of the basin and bathtub. Therefore, when purchasing, you must first know the distance between the basin / the bathtub and the wall. When selecting a wall mount faucet, the length of its spout must be selected correctly. The spout of the faucet should not be close to the edge of the basin or bathtub, otherwise it will affect the convenience of use. It is best to choose a faucet made of copper and a ceramic valve core, because of its good sealing performance, wear resistance, corrosion resistance and oxidation resistance.
We all dream of having a spacious bathroom, preferably a separate bathtub and shower, two sinks, and even a comfortable lounge chair to rest after bathing.
So, today we share with you 10 bathroom design principles. You can use some or all of these techniques to double your bathroom space.
01. Use White Color
One of the easiest ways to make a space look spacious is to use a lot of white: white tiles, white wall paint, white accessories, etc. White allows other colors to recede naturally, making the space look bigger. It can reflect any light instead of absorbing it.
The use of white is particularly effective in the bathroom. Since the bathtub, toilet and sink in the bathroom are basically white, the use of other white can make the space seamlessly connected, making the space transparent and creating a sense of expansion.
Using a lot of white does not mean pale and empty, lack of personality. Using different structural elements, such as light-colored stones or tiles with different textures, and a small amount of metal or wood intervention, can maintain a seamless appearance while also presenting the richness of the space.
02. Use Same Style Color
If you are not a fan of white, you can use warm beige, soft gray or even pink (pink blue, pink, etc.) to create a sense of spaciousness. Choose an elegant ceramic tile, and choose the matching color system for the rest of the wall. The overall effect is quiet and warm, and will not cause visual breaks and reduce your sense of space.
03. Use Floating Design
In a compact bathroom, balancing storage needs and a sense of spaciousness and freedom is a tricky issue. The suspended wash basin design is a good solution. It gives you a lot of space to store essentials. The empty space at the bottom is like an entrance and exit for air flow, which does not make people feel oppressed and tense.
04. Less is More
Less is more. If it is not necessary to have a large storage area, use small-sized wash basins to leave more open areas to make the space look bigger. If there is a bathtub next to the toilet, you need to leave enough space.
05. Use a mirror to enlarge the space.
A large enough mirror can double your space, especially in the bathroom. However, this kind of large mirror must be of good quality, and the size and thickness must be accurate, otherwise it will seriously affect the overall layout. A good mirror will have a very powerful effect, and you can make the room look perfect in just a few minutes.
06. Use Glass Doors
Another good way to expand the space is to use glass as a partition for the door or shower room. The visual extension makes the space look bigger. Especially in the shower.
If you are worried about privacy, you can use frosted or tinted glass, which can still achieve the effect of light transmission and will not make you feel cramped and depressed in the shower. If there is no special need, it is recommended to abandon the bathtub and install a shower room. The bathtub consumes a lot of valuable space, and the usage rate is extremely low.
07. Design a Suitable Alcove
Designing an open alcove in a suitable location can not only increase the storage space, but also increase the visual depth, making the wall look far beyond the real distance.
When designing alcove, you must communicate with professionals, because there will be many wires, pipelines, etc. in the wall of the bathroom.
08. Good Lighting
Good lighting is essential to make any space look bigger and more open, especially in bathrooms that don’t usually have much natural light. In addition, you also need good lighting in the bathroom to effectively perform shaving or makeup, so its importance does not need to be emphasized.
The key is to have a rich lighting scheme in the bathroom, and it is best to use multiple light sources in different locations. Ceiling lights (multiple bulbs can be used), or modern edge-lit mirrors will help you avoid shadows and make the space feel bright and open.
09. Create Long Lines
Whether your bathroom is typically rectangular or oddly shaped, you can always find a wall or area that is slightly longer than other places. Adding a shelf, a tile strip, or even a simple striped wall paint to these areas can help you lengthen the longest line in the room and draw the sight to the farthest position, giving the space a sense of extension.
10. Balance the Horizontal and Vertical Ratio
If your bathroom is already very long, narrow and tunnel-shaped, don't emphasize the length anymore, you must think more about stretching the width visually.
For example, in this long and narrow bathroom below, the tiles on the wall and the floor are laid in a horizontal splicing way, which invisibly increases the visual width, and the spatial balance becomes more harmonious.
Pull as you like. Return accurately.
When renovating the bathroom, the height of the faucet is a headache: if you buy a low one, you have to bend over when washing your hair or face; if you buy a high one, It's not convenient for the opening and closing of the mirror cabinet. On the other hand, it will cause water splashing due to the large drop...It is not a problem with the Aquacubic faucet!
Aquacubic faucet adopts pull-out design. With 360 degree sprayer head to realize free rotation and pull freely, the water can reach any place where the user needs it, and meet all the needs in the bathroom water process. After use, just let go. The built-in gravity hammer can help the faucet retract easily and quickly. Users can experience the pleasure of face cleaning and hair washing in a new way.
Long lasting new. Easy to clean.
The bathroom is full of moisture. In such an environment, water stains or fingerprints are easily left on the surface of the bathroom faucet. Scales will accumulate on the faucet after drying. They are difficult to clean and even gradually corrode the coating and form rust spots on the surface. To make the bathroom faucet last longer, you need surface treatment technology with easy-to-clean coating.
Aquacubic faucet adopts precision electroplating layer and SRS surface treatment technology, and passes 24 hours acid salt spray test. The surface has an elegant metallic luster. They are wear-resistant and corrosion-resistant. Faucet will be bright as new with a light wipe. You don’t have to worry about leaving fingerprints and watermarks when you touch it with wet hands. This reduces cleaning time.
The bathroom carries most of the cleaning work of a family. In turn it affects the living experience and life quality of the whole family. If you want to enjoy the exquisite life, you need the Aquacubic faucet that can be pulled freely to bring a fashionable bathroom to you!
Don't think that after the new house is renovated, it will be as pleasing as the propaganda album. After the new house is renovated, a large amount of decoration waste will be generated. Dust, stains and marks from the decoration will be left on the walls and glass. Just like a baby who was just born, she will have a cute appearance after washing and putting on clean clothes.
Cleaning the newly renovated new home is an important task after decorating the new home. It is also the most laborious task. Facing a messy and unstructured new home, you don’t know where to start. Summarize the first cleaning experience after the renovation. We hope it will be of reference significance to you.
01 Cleaning Service
Those who are clueless about the cleaning of a new house can choose the cleaning service of a housekeeping company. Housekeeping companies have their own routines and tools for cleaning work. It is also a way to hand over professional cleaning work to them. The premise is to choose a qualified and high-quality housekeeping company. Services include: house dust removal, cleaning up decoration garbage, wiping glass, cleaning the floor, decontamination and disinfection of kitchen and toilet, cleaning up decoration traces, etc.
Notes on cleaning service
1. Organize a list of cleaning precautions, and list some areas that need special cleaning to avoid omissions. The decoration materials of each family are different. It is necessary to tell them some precautions, such as which places and areas cannot use water or chemical cleaners. These need to be communicated clearly with the housekeeping company before starting work.
2. Clearly state the materials of walls, floors, furniture, etc. that need to be cleaned, and let the staff prepare appropriate cleaning tools.
3. Communicate clearly about the tools needed for cleaning, which are brought by the staff and which are prepared by us.
4. Communicate clearly on the disposal method of the cleaned up waste, whether to throw it away or keep it somewhere.
5. Supervision, including whether to do a good job in dust prevention and cleaning of dead ends.
02 Clean Up by Yourself
Some people are unwilling to hand over their new homes to strangers to clean up, so they do their own cleaning work. Cleaning in person is nothing more than two things: preparing tools and clarifying the order of cleaning.
Preparation of Tools:
1. These will be used to clean the wall.
Small brush, sandpaper (to polish the paint on the wall), shovel, glass spatula, wet paper towel (to wipe the wallpaper), ladder.
2. These will be used to clean the ground.
Vacuum cleaner, mop, broom, nano sponge, rag (use a discarded old bed sheet; the size can be cut at will. It is big enough), dust cover, garbage bag.
3. Protective Equipment
Shoe covers, gloves, aprons, masks.
4. Cleaning Utensils
Detergents, maintenance agents, disinfectants, glue removers.
Cleaning follows the order from top to bottom and from the inside to the outside.
Start cleaning from the room first, and then go to the kitchen and living room. The bathroom can be placed last, because the bathroom is a place where water is used repeatedly during the cleaning process.
Like kitchens and bathrooms, where there are wall tiles, they need to be cleaned from top to bottom to clean up the gaps in the tiles and the paint spots and glue stains on the surface.
03 Cleaning Techniques
During the decoration process, many traces of material adhesion will be left, and some cleaning skills are required.
Tape print: Use a damp cloth to wet it for a while before wiping.
Paint traces: Use paint remover or turpentine.
Marker marks: Wipe with a rag or damp paper towel with some alcohol.
Tile stains: Use special detergent for tiles to clean, paint and drawing pen fluid can be cleaned with turpentine, pyruvic acid or alkali.
Cement on glass: If it is a small cement stain, wipe it with a damp cloth and then scrape it off with a spatula. If it is a stubborn and large cement block, you can use the toilet cleaner to remove it. The effect is very good.
Tips: The toilet cleaner is acidic. Wear gloves when using it and don't think that the toilet cleaner is effective in removing cement and use it on tiles and marble floors. In addition, do not use alkaline soap at the same time when removing the cement on the glass.
04 Cleaning Can Be Done Separately.
In fact, if the new house cleaning work is done step by step during the renovation process, the subsequent cleaning will not be so laborious. Separate the cleaning work to these renovation steps:
1. After the water supply line and electricity are completed, and the walls and ground are leveled, the whole house can be cleaned and clean up the discarded decoration garbage.
2. When laying tiles, remind the workers to wipe off the cement stains on the surface of the tiles after laying the tiles.
3. After painting the wall and floor, you can clean it again.
If you have other new house cleaning experience, please leave a message to share with us.
As a manufacturer of sanitary products for more than 11 years, we have seen many customers whose bathrooms are really full of functions. Although it is small, the functions are still very diverse. Have to admire!
Modern decoration requires both practical functions and individual style, so the budget is often difficult to control. The bathroom space usage rate is high. If you can save it everywhere, rework and repair will occur, and the gains will outweigh the losses. At the same time, the cost of furniture and decoration can also be spent more or less. The following are some small details on the bathroom decoration, which can save costs time and time again!
1) Waterproofing is essential for walls.
Waterproofing in the bathroom is very important, not only to choose high-quality materials, but also to ensure professional painting. The wall waterproof in the wet area should be at least 180cm above the ground and 50cm for other places. The ground waterproofing generally needs to be brushed twice and a 24-hour closed water test should be carried out. Wall corners, water pipes, etc. should also be carefully done.
Ceramic tiles are the highlight of bathroom decoration. And the wall area is large. You can choose relatively economical tiles to ensure the waterproof performance. You can also directly paint with waterproof paint where it is not in the shower area. It will reduce cost.
Mosaics with rich patterns can enhance the visual aesthetics of the space. And to reduce material costs and manual laying costs, mosaics can be laid only on key positions. Tiles, waist line and top line can be selected according to your own needs to control the cost of decoration.
The original light-body wall is removed and replaced with a transparent glass wall, which expands the visual area of the space and also saves costs.
Mosaic paving requires a high labor cost, so you can find a large mosaic-like wall tile to pave the wall, which can save a lot of money. Since there are fewer gaps between large-size mosaic tiles, the amount of caulking agent is correspondingly reduced, which is often used for reference and selection in home decoration.
2) The floor area should be beautiful and non-slip.
Safety should be placed in the most important position, and slip resistance should be considered in the selection of floor tiles. At the same time, the human body will directly touch the ground, so the quality of materials should be paid attention to. Bright floor tiles are relatively slippery, so use them as little as possible in the bathroom, and use matte floor tiles or tiles with good anti-slip properties.
When paving the floor tiles, the slope must be appropriate, and the floor drain must be the lowest point so that the water can flow smoothly. The floor tiles should be made of whole tiles as much as possible, and the gap between the tiles should be controlled at about 2mm.
The area of decorative tiles on the ground is smaller than that of the wall. The use of interval paving can save the budget, and only use the same pattern of tiles to be separated by more than one tile.
If you want to create a low-cost bathroom with a natural texture, you can use wood-grain tiles instead of waterproof solid wood, which also has the characteristics of natural patterns, elegant colors, and easier matching with other sanitary wares.
Paving decal tiles in the bathroom can improve the monotonous bathroom style. In the actual construction process, the cost of laying decal tiles is much cheaper than mosaic.
When special-shaped handmade tiles are laid on the ground, they should be from the inside out, the gap between the tiles should be controlled within 8mm, and the height of the caulking agent should be level with the tiles. The paving of this kind of tiles should be carried out in sequence according to the serial number on the back to avoid waste caused by rework.
3) Cleverly arrange the exposed and concealed sanitary ware.
The bathroom is a place where multiple channels of water and electricity converge. In the early stage of renovation, it is necessary to choose quality water pipes, wires, etc. And the wiring must comply with the regulations to avoid water leakage due to design and material selection problems.
As the space expands and functions increase, there are more and more electrical appliances in the bathroom. If you want to install smart toilet lids, integral shower rooms, massage bathtubs, multi-functional bathroom cabinets, etc., you must first make the sockets during the decoration to avoid rewiring in the future and increase the trouble.
The plumbing renovation of the bathroom is most laborious. If you want to save this part of the cost, the pipeline must be open-lined, without slotting, and future maintenance can also save a lot of costs.
In addition, avoid excessive wiring when rebuilding waterways and circuits. Use multi-hole sockets as much as possible on the panel of the socket. Under the premise of the same number of wires, you can plug in more electrical appliances. The wiring of the space is reconstructed with open wires, and the wires are routed from the top. The outer wall of the pipe is painted with waterproof paint, which saves a lot of labor costs and is also convenient for maintenance.
The bathrooms are uniformly decorated in black and white tones, simple and generous. The upper and lower water pipes of the sanitary ware are made of metal material, which has a long service life and is not easy to be damaged.
The space matching has been cleverly designed. The cement wall is matched with solid wood floor tiles, which is elegant and warm, satisfying practical functions and beautiful.
4) Shower Area
The quality of the glass used in the shower room is closely related to the safety of the bathroom. Fine tempered glass is generally difficult to break, and it will not hurt people when broken. Therefore, when choosing, don't be greedy for temporary cheapness, and try to choose high-quality, well-reputed brands.
The frame of the shower room is usually made of aluminum alloy, and the surface is sprayed with plastic, so it is not corroded or rusty. The thickness of the main frame aluminum alloy is preferably 1.1mm or more, which is not easy to deform.
In addition to professional brand shower rooms, the shower area can also be separated from dry and wet areas with various partitions. Common glass partitions only need to be installed on one side when combined with the wall, which saves costs by using less materials.
At the same time, the installation of the shower room can be omitted. The base of the shower room mainly plays the role of heat preservation and drainage, and the material is mostly acrylic.
The shower area is separated by a glass wall, and the ground is transitioned by steps to create a semi-enclosed shower space. The glass partition is directly fixed with hardware without reaching the top, which gives the space better permeability.
A wall serves as a partition, separating the wash area from the shower area. The interior of the wash area is covered with ceramic tiles, the exterior is painted with waterproof paint, and the key parts are strengthened.
5) Wash Area
The floor drain is most commonly used for sink, and the wall mount type can be used for more advanced spaces. It is best to have all S-bends to prevent upward odor. Basins are divided into above-counter basins, under-counter basins and wall-mounted basins. Above counter basins for households are more suitable and easy to install. The under counter basin is suitable for a large area bathroom, and the installation is relatively complicated.
Small-space or low-budget families can abandon the overall bathroom cabinet, and use a transparent iron frame to save space and leave more space for the legs. Mirror cabinets and recessed cabinets are more suitable for small spaces and complete the storage function of the bathroom. To reduce the cost of decoration, you can choose a single color and simple style in the decoration, and match it with retro copper-colored, metal-colored faucets or mirror lights to create highlights.
Build the washstand with cement, and place storage baskets underneath. The wall-mounted faucet is highly decorative, but the size must be measured accurately in advance, otherwise it cannot be installed, which will affect the use.
There is no special furniture under the basin; only metal racks are used to save costs and place toiletries.
Aquacubic is a professional manufacturer for bath and kitchen products since 2010. We have rich experience and passion in bath and kitchen industry and appreciate your contacting and business. Look forward to cooperating with you. Thanks a lot!
In addition to the practicality of the apartment renovation, we also pay attention to its beauty. For example, choose wall-mounted toilets and washbasins; choose concealed baseboards; hide all the pipes; improve the overall aesthetics!
Concealed showers are more beautiful than exposed showers.
There are mainly the following 3 ways to install the shower:
1) Exposed installation: the water inlet pipe and mixing valve of the shower are exposed outside, which is not beautiful enough;
2) Concealed pipe installation: The inlet pipe is buried in the wall and the mixing valve is outside. This is most commonly used method;
3) Concealed installation: Completely opposite to the first type, the inlet pipe and the return valve are installed inside the wall. Leaving only the switch and the water outlet outside. Although it is beautiful, the process is complicated.
For concealed showers, there are also two different styles:
1) Top sprayer and hand shower
Look at the picture, the top shower head is matched with a hand-held shower head at the bottom. In this way, you need to determine the size of the shower head before renovation. And do the drilling and wiring layout. In terms of installation, this method is relatively simple.
2) With additional side spray
This is based on the former, plus a side spray function. During renovation, pre-installed in-wall boxes and multiple valve cores are required to match the water outlet. You can imagine how complicated this approach is! How to install it? Look down.
First determine the number of side nozzles (usually 2-6); the in-wall installed valve core has multiple outlet connection ports, from the valve core to the main water inlet, other outlets, top spray showers and hand showers; Secondly, cement leveling is required between the valve core and the wall, and in-wall installed parts are also used to stabilize; then leveling, waterproofing and pressing are performed to see if there is any leakage; the last step is to sticking ceramic tiles.
Compared with the exposed installation, the appearance of the concealed shower is certainly more attractive. However, the maintenance is complicated and cannot be ignored. The water pipe fittings of the exposed shower are all on the outside. If the concealed shower needs to be repaired, we can only break the wall! But if you choose a good quality shower, except for the water pipe problem, you don't need to break the wall under normal circumstances.
If you really like the appearance, it is not a big problem to choose a concealed shower. But if you are still worried about renovation and later maintenance, it is recommended not to try it.
Shower Purchase Skills
1. When choosing a shower, try to make the shower tilted (to see the water effect). If the top spray holes are obviously small or there is no water at all, it shows that the internal design of the shower is very low. It is impossible for the user to have a comfortable experience.
2. Look at the coating and valve core. Under normal circumstances, the brighter and more delicate the surface of the shower, the better the coating process. The high-quality shower uses high-quality ceramic valve core, which has high hardness and wear resistance, and is not easy to drip. The rotating adjustment handle is also very smooth.
3. Everyone knows that if the shower is used for a long time, there will be scale and impurities deposits, which will block the water outlet. If the mesh cover cannot be cleaned, the shower will not discharge water normally; in order to avoid the blockage of the water outlet due to poor water quality. All the shower nozzles should stick out for easy cleaning.
4. Shower accessories will directly affect the comfort of our shower. This cannot be ignored. For example, whether the lifting rod of the shower is flexible. Whether the shower joint is equipped with anti-twist ball bearings. Whether there is a rotation controller on the lifting rod, etc.
5. The water-saving function of the shower is the key point to be considered when purchasing the shower. Some showers use a steel ball valve core, and are equipped with a hot water controller, which can adjust the inflow of hot water into the mixing tank, so that the hot water can flow out quickly and accurately. This type of shower with a reasonable design saves 50% of water compared to ordinary showers.
1. Do a good job of cleaning up during installation, especially the valve core. During the decoration, it is inevitable that decoration dust or even large particles of impurities enter the water supply pipe. If it is not cleaned up, these impurity particles will enter the valve core of the shower faucet, easily causing blockage or even destroying the internal structure of the valve core. If the shower has little water output, it is very likely that the cleaning work is not in place.
2. To ensure safety, equipotential terminals are indispensable.
An electric shock prevention system is indispensable in the bathroom: equipotential terminal. After all, compared with other spaces, the bathroom is accompanied by water all the year round, and the risk is relatively high. Connect with the equipotential terminal to prevent leakage, electric shock, and avoid dangerous situations.
There are a large number of shower options. So everyone can try to choose different showers. Traditional showers have gradually been eliminated. We must learn to keep up with the trend in renovation project.
Aquacubic is a professional manufacturer for bath and kitchen products since 2010. We can provide full solution for construction project contractors and wholesalers. The products include faucets, sinks, basins,
bathroom accessories, shower sets, shower rooms, ceramic basins, bathtubs, etc.
Look forward to cooperating with you.
Thanks a lot!
Guangdong sanitary ware production area: all kinds of sanitary products.
Guangdong's production areas are mainly concentrated in Foshan, Kaiping, Zhongshan, Chaozhou. It is the region with the most complete domestic bathroom industry chain, the most enterprises, and the most well-known brands. Guangdong sanitary ware production area includes all kinds of sanitary products, including ceramic sanitary ware, hard sanitary ware, etc. At present, no production area can compare with Guangdong in terms of industrial intensification. Aquacubic’s two production sites are located in Foshan, Guangdong.
Tangshan sanitary ware production area: mainly ceramic sanitary ware.
Tangshan ceramics has a long history. It is the main ceramic producing area in China. At present, Tangshan has been recognized as "Hebei Province Ceramic Products (Tangshan) Export Base", "China Building Material Export Base" and "National Foreign Trade Transformation and Upgrade Professional Demonstration Base".
Nan'an sanitary ware production area: mainly hardware plumbing.
Nan'an, the hometown of water heating in China, is centered on Luncang Town, the "Hometown of Water Heating in China", and Yingdu Town, "China's Water Heating Valve Base Town". Nan'an people's supply and marketing forces spread all over the country, occupying more than 70% of the country's plumbing valve market sales.
Zhejiang sanitary ware production area: mainly hard sanitary ware.
At present, Zhejiang sanitary ware industry has formed economic development sectors such as Hangzhou leisure sanitary ware base, Jiaxing Pinghu sanitary ware base, Wenzhou plumbing equipment production base, Taizhou sanitary ware base, Ningbo plumbing equipment and sanitary fittings production base.
Changge sanitary ware production area: mainly ceramic sanitary ware.
In November 2009, the China Building and Sanitary Ceramics Association officially awarded Changge City the title of "Central China Sanitary Ware Industry Base", marking the first national sanitary ware industry base to settle in Changge, Henan.
Chinese manufacturers have mastered the design, research and development, production, sales and service of sanitary products, opening up the entire industrial chain. As China enters the era of quality, more and more consumers are willing to pay for quality, and the quality of products in the sanitary ware market will be even more improved.